Virtual Museum of the Vietnam War

Technical Bulletin 746-93-1

Section ( IV ) Special Markings

---
Section ( I ) General
Section ( II ) Descriptions
Section ( III ) Identification Markings
Appendix
---

12 - Safety Markings.

  1. Vehicles used for the quantity transportation of gasoline, fuel oil, or other flammable liquids will be marked on both sides and rear with the word "Flammable" in 6 inch letters, and the words "No Smoking Within 50 Feet" in 3 inch letters and numerals. The marking will be placed in two lines, with the word "Flammable" on the top line. The marking will be applied in the same colour as the vehicle registration marking.
  2. Vehicles carrying explosives or other dangerous materiel will be marked as follows:
    1. When used for the transportation of such dangerous materiel over public highways, vehicles will be marked or equipped with appropriate placards in accordance with AR 55-355.
    2. When used for the transportation of such dangerous materiel to training areas, vehicles will be marked or equipped with placards on both sides and ends. The words "Explosives" will be marked in white letters not less than 3 inches high on a red background in accordance with AR 385-63. Reflectorized markers should be used when available.
  3. When authorised by the responsible commander, stripes of a contrasting colour may be applied to certain vehicles and equipment used in a non-tactical area, which, because of size, construction, or function, present a possible hazard. These stripes are applied to permit vehicles to be more readily seen by drivers of other vehicles. They are normally applied to the rear of such vehicles; they may, however, be also applied to the front or certain side surfaces if required.
    1. The stripes will be applied across the face of the bumper, or across the width of the vehicle on a flat surface above the bumper in a band not to exceed two feet in height. Other appropriate surfaces may be used when necessary.
    2. Width of the stripes will be four  inches with a four inch space between stripes. They will be inclined at a 45' angle in opposite directions from the centreline of the vehicle, to form an inverted V pattern.
    3. Gloss yellow, Colour Chip No. 13538, will be used for stripes on vehicles painted olive drab or other dark colour.
    4. Gloss black, Colour. Chip No. 17038, will be used for stripes on vehicles painted yellow or other light colour.
  4. DA Label 76 (A Good Driver) for promoting safe driving practices, may be requisitioned through normal publications supply channels, and will be applied to all motor vehicles as follows:
    1. Truck, utility, 1/4, T, M38 -- Directly under the left windshield wiper motor.
    2. Truck, utility, 1/4, T, M38Al -- Centre of the map compartment door.
    3. Truck, utility, 1/4, T, M151 -- Windshield frame, below the glass and to the left of the steering column.
    4. Trucks, 3/4, T, and over -- Upper and forward end of the left front inside door panel.
    5. Tanks, self propelled artillery, personnel and cargo carriers,high speed and cargo tractors, and tank recovery vehicles Left bulk head at operators eye level.
  5. All motorised materials handling equipment will be marked with the legends "No Smoking" and "No riders".
    1. These legends will be placed on a surface facing the operator.
    2. The markings will be applied in 1 inch letters of the same colour as the registration markings.
    3. The markings may be applied horizontally to read left to right or vertically to read top to bottom.

13 - Technical Markings.

  1. Tire Pressure. The prescribed vehicle tire pressure will be marked on the dash of all motor vehicles and pneumatic tired equipment. This marking will also be applied to the fenders above each wheel or, if fenders are not used, to the body or frame immediately above each wheel. On towed vehicles or equipment, this marking will be applied to the body or frame immediately above each wheel. On tandem axle vehicles the marking will be centred between the two wheel sets.
    1. The markings will consist of the numerals representing the proper pressures, preceded by the letters TP.
    2. Letters and nu merals will be 1 inch high and in the same colour as the registration marking.
  2. Maximum Speed. When maximum speed is specified by a manufacturer, or in an applicable technical manual, and when appropriate operation plates are not available, the maximum speed of the vehicle in its highest range and gear ratio will be marked on the dash.
    1. The marking will consist of the numerals representing maximum speed, preceded by the abbreviation "Max Speed".
    2. Letters and numerals will be 1 inch high and in the same colour as the registration markings.
  3. Arctic Lubricated. All vehicles and equipment processed with special arctic lubricants and/or other materials for operation in cold climates will be marked with a temporary marking as follows:
    1. The words "Arctic Lubricated" will be marked in the following order of preference:
      1. Adjacent to the agency identification or registration marking on each side of the vehicle or equipment.
      2. Adjacent to the name or identification plate.
      3. On another conspicuous location in order that the markings may be readily seen prior to operation or use. Specific locations may be prescribed in applicable technical publications for the vehicle or equipment.
    2. Letters of the marking will be 1 inch high and in the same colour as the registration marking.
    3. The marking will be kept in a legible condition until the vehicle or equipment is de-processed, and will then be thoroughly removed.
  4. Engine Hood Safety Hook. All tactical use wheeled vehicles which are equipped with an engine hood safety hook will be marked with the words "Warning: Secure Hood in Raised Position with Safety Hook Before Servicing Engine".
    1. The marking will be applied at the rear area on the underside of the hood panel.
    2. Letters of the marking will be 1 inch high, and white.
  5. Crane Boom. Boom extension markings are required to assure operation within boom radii limits specified on the crane safe load data plates.
    1. Boom markings will be applied in the permanent method of marking. Colour will be the same as the registration markings.
    2. Procedure for Trucks M60 and M108.
      1. Retract boom and retain in horizontal position.
      2. Measure, scribe, and mark a 3/1 inch vertical stripe along the outer edge of the shipper, extending the stripe onto the boom (figure 10).
        Figure 10
        Figure 10: Boom markings ( boom retracted )
      3. To the right of and parallel with the stripe, mark "8 Ft" in 2 inch letters.
      4. Mark a horizontal arrow on the shipper pointing to the stripe.
      5. Extend the boom to its maximum length.
      6. Measure from the "8 Ft" stripe. Scribe and mark 3/4, inch vertical stripes at intervals of 12 inches along the boom (figure 11).
        Figure 11
        Figure 11: Boom markings ( boom extended )
      7. Mark the second stripe "9 Ft", and each succeeding stripe consecutively through "16 Ft", in each case to the right of and parallel to each stripe.
    3. The procedure for Truck M60- is the same as for Trucks M60 and M108, except that the first stripe will be marked "10 Ft" and each succeeding stripe will be marked consecutively "11 Ft" through "18 Ft".
    4. The procedure for Truck M246 is the same as for Trucks M60 and M108, except that the first stripe will be marked "111/2 Ft". The second stripe is to be measured, scribed, marked, and labelled "12 Ft". Each succeeding stripe will be marked consecutively through "26 Ft".
  6. Excessive Fuel Tank Pressure. This paragraph applies to tactical transport vehicles, and is intended to reduce the possibility of fuel spillage due to fuel tank over filling and subsequent fuel explosion, regardless of fuel type.
    1. If the fuel tank filler cap is a relief valve type, but does not bear a warning decal reading "Pressurised: Open Slowly", the warning note "Pressure: Open Slowly" will be marked in 1 inch white letters on the cap or on the fuel tank near the filler pipe.
    2. On fuel tanks, where a mark would be readily visible, measure 2 inches down from the top of the tank and mark a 1/4 x 8 inch line, with the following note in 1 inch white letters: "Caution: Do Not Fill Above This Line". See figure 12.
      Figure 12
      Figure 12: Fule tank marking
    3. On vehicles where a mark on the fuel tank would not be readily visible, mark the following note in 1 inch white letters as near as possible to the filler pipes: "Caution: Do Not Overfill-Allow for Expansion".
  7. Maximum Safe Fuel Acceptance Rates. These marking instruction,-, for indicating maximum safe fuel tank filling rates are published for the benefit and safety of personnel concerned with refuelling operations. The maximum safe fuel acceptance rate will be marked on each fuel tank near the filler cap. When the fuel tank is enclosed the marking will be applied on the exterior surface of the enclosure adjacent to the fuel tank Tiller cap access cover. The marking may be applied on one, two, or three lines, dependent on available space. When multiple lines are required the following examples will govern.
    2 Lines:
    Max. Safe Fuel
    Accept ______GPM

    3 Lines:
    Max. Safe
    Fuel Accept
    ______ GPM
    1. Refer to table B for the safe fuel acceptance rates on all vehicles. As additional information becomes available it will be included in changes to this technical bulletin.
    2. The marking will be in 1 inch white letters.
  8. Calibration Insignia. All calibration vehicles will be marked with a calibration insignia in the form of a decal. These decals will be applied to the upper forward corners on each side of the M292 Expandable Van (figure 13). On other types of calibration vehicles (vans, panel trucks, etc.), the decals will be applied in the most appropriate location on each side, dependent on surface size, window location, and surface texture.
    Figure 13b Figure 13a
    Figure 13: M-292 expandable van ( calibration )
  9. Capacity and Weight. All motorised materials handling equipment will have the capacity marked on each side. The marking will consist of the numerals showing the applicable pounds followed by the letters CAP. The actual weight of the equipment will also be marked on each side, in numerals, to show the applicable pounds, followed by the letters, MTWT. Letters and numerals will be one inch high, in the same colour as the registration marking. Refer to figure 6.
  10. Other Instructions. Other necessary technical instructions may be marked on appropriate surfaces as required or authorised by the responsible command.
    1. Such markings will be applied in letters and numerals normally 1 inch in height but not less than 1/2 inch.
    2. Colour of the markings will be white or black, whichever affords the greater contrast with the surface colour. If practicable, the colour chosen will be the same as the registration marking.
    3. Temporary instructions will be applied with removable vinyl markings or gasoline soluble paint.

14 - Weight Classification.

  1. All single vehicles with a gross weight of over 3 tons, and all trailers with a rated payload exceeding 11/2 tons, are classified for the purpose of bridge crossing, per FM 5-36. Each single vehicle and vehicle combination has a classification number for empty, cross-country loading, and highway loading. The classification numbers are used to determine whether a bridge, correspondingly classified, can be safely crossed.
  2. All applicable self-propelled vehicles not towing other vehicles will carry a circular sign of 9 inch diameter with the vehicle's classification number in black on a yellow background. This will normally be located on the front of the vehicle toward the vehicle's right side and below the driver's line of vision.
  3. All applicable self-propelled vehicles towing other vehicles will carry a sign similar in size, design, and location except that the classification number of the vehicle combination will be shown with the letter C in red above the number. A 6 inch yellow circle with the basic vehicle classification number in black will be marked on the right side of the vehicle in a conspicuous location. The towed vehicle will be similarly marked with its basic classification number.
  4. When the classification number of the vehicle is not subject to change, the marking may be applied directly on a suitable surface. On vehicles painted in gloss colours, the markings will be gloss yellow, Colour Chip No. 13538; gloss black, Colour Chip No. 17038; and gloss red, Colour Chip No. 11136. On vehicles painted in semi-gloss or lusterless colours, the markings will be lusterless yellow, Colour Chip No. 33538; gloss black, Colour Chip No. 17038 and gloss red, Colour Chip No. 11136. When the marking is applied directly to vehicles painted in the same or similar colour, the circumference of the circle will be outlined with a black circle .3/4, inch wide.
  5. In usage's where the classification number may change, a sign kit will be utilised which consists of a 9 inch metal disk, a retaining plate, and two sets of five different numeral plates. By installing the retaining plate, the numeral plates will be locked in place. The sign has black numerals on a yellow background and a red C on one side of the retaining plate (figure 14).
  6. The following weight classification sign kit is being supplied initially with mounting brackets and hardware.
    Name Part No. Federal stock No. Qty.
    KIT: vehicle class sign, w/brackets and hardware
    Consisting of:
      9905-565-6267 1
    6 ea BOLT, MACHINE: hex-hd, S, cd- or zn-pltd,
    5/16-24UNF-2A x 3/4*
    120741 5306-012-0741  
    2 ea BOLT, MACHINE: hex-hd, low-carb-S, cd-
    or zn-pltd, 3/16-24UNF-2A x 1 3/4
    123798 5306-012-3798
    1 ea BRACKET: unit, lg**    
    1 ea BRACKET: unit, short**    
    1 ea DISK: vehicle class sign, 9-in.    
    6 ea NUT, PLAIN, HEXAGON: S, cd- or
    zn-chromate-fin., 5/16-24UNF-2B, 1/2w, 17/64 thk*
    120368 5310-012-0368
    2 ea PLATE: numeral, 0 one side, 1 other side    
    2 ea PLATE: numeral, 2 one side, 3 other side    
    2 ea PLATE: numeral, 4 one side, 5 other side    
    2 ea PLATE: numeral, 6 one side, 7 other side    
    2 ea PLATE: numeral, 8 one side, 9 other side    
    1 ea PLATE: retaining, C on one side    
    6 ea WASHER, LOCK: int-teeth, S, cd- or zn-pltd,
    6/16 in. screw size
    138538 5310-013-8538
    *Hardware items not required for the specific installation procedure will
      be returned to stock
    **Brackets not required for the specific installation procedure will be scrapped.
  7. In addition, a replacement kit, itemised below is authorised for the replacement of lost or damaged numeral plates and retaining plates.
    Name Federal stock No.
    KIT: retaining and numeral plate replacement,
    for vehicle class signs Consisting of:
    9905-565-6268
    1 ea PLATE: numeral, 0 one side, 1 other side.  
    1 ea PLATE: numeral, 2 one side, 3 other side.
    1 ea PLATE: numeral, 4 one side, 5 other side.
    1 ea PLATE: numeral, 6 one side, 7 other side.
    1 ea PLATE: numeral, 8 one side, 9 other side.
  8. A vehicle weight classification sign kit, as below is authorised for the replacement of lost described herein, will be installed on the front or damaged numeral plates and retaining of each vehicle except:
    1. All trailers.
    2. Vehicles having a gross weight of 3
    3. Vehicles having standard classification numbers higher than 99.
    4. Vehicles having rated payloads of 3/4, to 11/2 tons. This exception does not apply to vehicles authorised for towing loads.
    5. Vehicles with fixed loads (such as tanks, self-propelled guns, etc.).
  9. Front classification signs for vehicles included in h(3), (4), and (5) above will be painted directly on the vehicle. Side classification signs, where applicable, will also be painted directly on the vehicle.
  10. These vehicle weight classification sign kits can be installed on vehicles in different ways. For example, in the case of Cargo Truck, M211, the sign can be installed on the brush guard, on the splash shield, or in an upright position on the fender. The choice of method is left to the using organisation.
    1. Location.
      1. The classification sign will be installed on the vehicle in one of the following locations:
        1. Right front fender.
        2. Right side of brush guard.
        3. Right front section of hull.
        4. Right side of centre front bumper splash shield.
      2. The sign will he placed below the driver's line of vision and will be positioned so that it will not block headlamps, marker lights, blackout lights, air intakes, etc.
    2. Installation.
      1. On brush guard.
        1. Paint the long universal bracket (channel) with rust-inhibiting enamel.
        2. After the enamel has dried, position the bracket so that the two holes in the bracket align with two bolt holes (9 o'clock and 3 o'clock positions) in the sign. Assure that the flat bearing surface of the bracket faces toward the sign. Install one bolt (1 3/4 inches long) 123798, one washer 138538, and one nut 120368. Turn nut two or three turns.
        3. With the bracket in a vertical position, insert it between two bars of the brush guard at the desired location. With one hand, reach behind the brush guard and adjust the bracket to a horizontal position. With the other hand, install another bolt (1.3/t inches long), washer, and nut. Tighten both bolts, but apply only enough torque to secure the sign to brush guard. Excessive torque will cause the sign disk to bend. Figure 14 shows the sign installed on brush guard.
      2. Figure 14
        Figure 14: Vehicle weight classification sign installed

        Caution:    If it is found that the vehicle classification sign seriously obstructs air flow to the radiator, as indicated by engine overheating, remove sign from brush guard and Install sign elsewhere.

      3. On sloping fender. Install the sign as indicated in 1 and 2 below only when the slope of the fender is less than 30' from vertical. When the slope of the fender is more than 30' from vertical, install the sign in a vertical position, as outlined in (c) below, to insure readability of the sign.
        1. Position the sign in the desired location on the fender and, using the sign as a template, drill two 1%2inch holes in fender to align with bolt holes in the sign at the 9 O'clock and 3 O'clock positions.
        2. Install the sign to the fender with two bolts 120741 (3/4 in. long), two washers 138538, and two nuts 120368. Tighten bolts securely (figure 15).
      4. Figure 15
        Figure 15: Sign installed on sloping fender (slope angle more than 30' from vertical)
      5. In a vertical position on fender or on splash shield.
        1. Alter the long universal bracket (channel) in accordance with figure 16.
          Figure 16 Figure 16
          Figure 16: Alteration of brackets
        2. Paint both the altered bracket and the short universal bracket (angle) with rust-inhibiting enamel.
        3. After the enamel has dried, position the long leg of the short bracket on the back of the sign and align two holes in bracket with the two lower bolt holes in the sign.
          Note. When installing the sign on a horizontal surface, position the short leg of the bracket so that it faces rearward (figure 17).
          Figure 17
          Figure 17: Sign installed on splash shield
          When installing the sign on a sloping surface, position the short leg of bracket so that it faces forward (figure 18).
          Figure 18
          Figure 18: Sign installed on sloping fender ( slope angle more than 30' from vertical )
        4. Install bracket to sign with two bolts 120741 (3/4 in. lg), two washers 138538, and two nuts 120368.
        5. Position the sign in the desired location on the fender or splash shield. Bend short leg of bracket, as required, to conform to the contour or slope of fender.
        6. Using the short leg of the bracket as a template, drill two 11/32-inch holes in fender or splash shield.
        7. Attach the sign to the fender or splash shield with two bolts (3/1 in. long), two washers and two nuts.
        8. Secure the altered long universal bracket to the sign with one bolt (3/4 in. long), one washer, and one nut. (Insert bolt in hole located between two stacks of numeral plates on sign).
        9. Drill an 11/32-inch hole in fender or splash shield to correspond with the hole in the altered bracket and secure the bracket with one bolt (3/4 inch long), one washer, and one nut. Figure 17 shows sign installed on splash shield. Figure 18 shows sign installed on sloping fender.
  11. Instructions for unlocking and locking the retaining plate is as follows:
    1. Unlocking retaining plate. With the thumb of one hand, press down firmly on one stack of numeral plates (figure19).
      Figure 19
      Figure 19: Unlocking the retaining plate
      With the other hand, press down gently on the retaining plate and pivot the plate away from the lock pin. To remove retaining plate completely, press down firmly on the remaining stack of numeral plates and free retaining plate from the other lock pin.
    2. Locking retaining plate. Assure that five numeral plates are stacked on each anchor pin with the two top plates showing the desired classification number. If the vehicle is to be used in combination, position the retaining plate so that the red C on one side of the plate will be visible. If the vehicle is to be used singly, position the retaining plate so that the red C will not be visible. Press down firmly on the top of one stack of numeral plates and slide the retaining plate onto the lock pin until the plate snaps in place. Repeat the procedure for the remaining stack of plates and lock the retaining plate to the remaining lock pin.
  12. See table C for vehicle weight classification data. For vehicles not listed, or for which no similar vehicle is listed, refer to TM 5-312, only in the event that no qualified engineer is available.

15 - Operation and Designation Plates.

  1. These plates as provided on vehicles and equipment will be kept clear and free from paint at all times.
  2. Operation plates contain data or instructions on vehicle operation and will be installed within the normal view of the operator when in an operating position. The plates will include:
    1. Road speed plates. To prescribe the maximum permissible speed for operation in each gear ratio and range.
    2. Shift diagram plates. To show the location of each position of the transmission, transfer, and /or power takeoff.
  3. Operation plates containing precautionary instructions to avoid personnel injury or equipment damage will have a red background. This applies to new plates of photosensitive anodised aluminium, conforming to type H, MIL-SPEC 15024. Existing plates will be replaced only when no longer serviceable.
  4. Designation plates contain data pertinent to the vehicle or equipment, but are not required for actual operation. They will be located in convenient position without creating confusion with operation plates. The plates will include:
    1. Name or identification plates. To show nomenclature, manufacturer, model, serial number, stock number, contract number, date of delivery to the Government.
    2. Data plates. To show empty weight, maximum payload, and/or gross weight, weight on each axle, and/or maximum towed load for highway and cross-country; centre of gravity empty and loaded, shipping cubage, overall and reducible dimensions, and other pertinent linear and angular dimensions.
    3. Servicing data plates. To show fuel capacity and minimum octane, cooling system capacity, draining instructions, tire pressures for terrain conditions, lubricant data for different temperature ranges, and other servicing data for the vehicle, components or equipment installed.
    4. Responsible agency plates. To show the Commodity Command or agency responsible for the procurement and/or maintenance of the vehicle or its chassis, body, and /or equipment.
    5. Publication plates. To show the manuals (operator's, maintenance, and supply) and lubrication order applicable to the vehicle.
  5. Designation plates may be combined plates when space conditions warrant.

16 - Ambulance Marking - Military Design Vehicle.

  1. Truck, Ambulance, 1/4 Ton, 4x4, M170 (Series).
    1. An 18 inch red cross on a 20 inch square white field will be marked on each canvas side curtain directly to the rear of the canvas side doors.
    2. An 18 inch red cross on a 20 inch square white field will be marked on the rear of the vehicle. The upper half of this marking will be applied on the canvas rear doors and the lower half on the tail gate, centred with the centreline of the vehicle, in order that the full marking is shown when the rear doors are closed.
    3. A 45 inch red cross on a 48 inch square white field will be marked centred on the canvas roof.
  2. Truck, Ambulance, 3/4 Ton, 4x4, M43 (Series).
    1. The word "Ambulance" will be marked in 3 inch high white letters, centred three-quarters of an inch above the windshield.
    2. A 3 inch red cross on a 4 inch square white field will be marked to each side of and in line with the word "Ambulance" above the windshield.
    3. A 36 inch red cross on a 39 inch square white field will be marked on each side of the body below the roof joint and centred above the rear wheels.
    4. A 33 inch red cross on a 36 inch square white field will be marked on the rear door panels directly below the windows and centred on the vertical centreline of the vehicle.
    5. A 60 inch red cross on a 64 inch square white field will be marked on the roof 14 inches from the rear of the vehicle (figure 20).
      Figure 20
      Figure 20
      Figure 20
      Figure 20
      Figure 20: Ambulance marking for military design vehicles
  3. Other Vehicles. Vehicles other than the ones enumerated which are intended for such usage and which are affected by international agreement concerning such vehicles will be marked in a similar manner.
  4. National Symbol. The National Symbol will not be applied to Medical Service vehicles.
  5. Sizes. The' sizes of the red crosses specified are measured between the ends of opposite limbs. Each limb of the cross will be a square having sides equal to one-third the size of the cross.
  6. The Army Medical Service Insignia. The Army Medical Service insignia consisting of a red caduceus on a circular white field will be applied to each side of the ambulance. Caduceus to be Type 1, MS 16686.
    1.     The circular white field will be 91/2 inches in diameter.
    2.     The red caduceus symbol will be 6 inches high.
    3.     The letter U will be centred to the left of the caduceus symbol; the letter S will be centred to the right. These letters will be red, 1 1/2 inches high.
  7. M170 Series Ambulance. The insignia will be applied each side of the vehicle body to the rear of the rear wheel.
  8. M43 Series Ambulance. The insignia will be applied on each side of the vehicle body centred horizontally forward of the red cross emblem. The top of the white circle will be level with the top of the horizontal red cross arm. The legend "Army Medical Service" will be applied centred 31/2 inches below the caduceus insignia, in 11/2 inch high white letters.
  9. Ambulance Colour Markings. The following colours will be used for ambulance markings, as applicable:
    1.     Gloss red, Colour Chip No. 11136, and Gloss white, Colour Chip No. 17875 on vehicles painted gloss or semigloss olive drab.
    2.     Lusterless red, Colour Chip No. 31136 and lusterless white, Colour Chip No. 37875 on vehicles painted lusterless olive drab.

17 - Military Police Markings-Military Design Vehicles.

  1. Truck, Utility, 1/4-Ton, 4X4.
    1. On the M38, M38A1 and M151 Trucks, a white disc, 16 inches in diameter with the words "Military Police" in 3 inch black letters located .around the circumference of the disc, 1/2 inch from the disc edge, will be attached to the centre of the spare wheel on the rear of the vehicle. The sign will be locally fabricated from 16 gage sheet metal or thicker. The disc will be attached by means of a bracket made from strap iron, 1 inch wide and 1/8 inch thick.
    2. In addition:
      1. M38 Truck. A detachable white sign, 5 inches high and 40 inches long, with the words "Military Police" in 3 inch high black letters will be mounted on the windshield panel below the glass. The sign will be locally fabricated from 16 gage sheet metal or thicker, and will be bolted to the windshield panel with ? inch bolts through existing holes in the panel.
      2. M38A1 Truck. A detachable white sign, 3 1/2 inches high and 59 1/4, inches long, with the words "Military Police" in 3 inch high black letters, will be mounted on the windshield panel below the glass. The sign will be locally fabricated from 16 gage sheet metal or thicker and will be attached to the windshield panel with sheet metal screws.
      3. M151 Truck. A detachable white sign, 5 inches high and 36 inches long, with the words "Military Police" in 3 inch high black letters, will be mounted on the windshield panel below the glass. The sign will be locally fabricated from 16 gage sheet metal or thicker and will be attached to the windshield with sheet metal screws.
      4. Motorcycle, solo, will be marked with a white band, 3 inches high, with the words "Military Police" in 2 inch high black letters, across the front of the windshield directly above the horizontal support. When not obstructed by lights or sirens, the band may be placed below the support.
  2. Application. The military police markings described herein will be applied with pressure sensitive adhesive vinyl markers, non-Reflectorized and conforming to Military Specification MIL-D-8634B. For the vehicles identified above, pre-printed markers conforming to the size and shape of the fabricated signs will be applied directly onto the signs before attaching to the vehicle. If pre-printed markers are not available, plain white vinyl may be used with the wording applied in individual black letters. If vinyl markers are not available and cannot be obtained, the markings may be applied in the stencil and paint method. The following colours will be used:
    1. Lusterless white, Colour Chip No. 37875.
    2. Gloss black, Colour Chip No. 17038.

---

Appendix ( I ) Tables.

Colour and Marking of Military Vehicles, Construction Equipment,
and Materials Handling Equipment Index Page

main page